(a) (d) (b) (e) 1. part no. expression : (b) dimension code (c) type code (a) series code 2. configuration & dimensions : a superworld electronics (s) pte ltd 3. schematic : (d) inductance code : 4r7 = 4.70uh (e) tolerance code : m = 20%, y = 30% pg. 1 12.50.3 b c 4.80.2 d 4.70.3 e unit:m/m 13.50.5 2.30.3 (c) (f) (f) f : rohs compliant 4r7 1150 a b c d e 4. materials : p i c 1 2 0 5 h p 4 r 7 m f - smd power choke coil pic1205hp series (g) note : specifications subject to change without notice. please check our website for latest information. 06.11.2015 (g) 11~99 : internal controlled number g 8.0 h 14.2 l 5.0 recommended pc board pattern l h g (a) core (b) wire (c) terminal (d) ink (e) paint 5. general specification : g) part temperature (ambient+temp. rise) : should not exceed 125c under worst case operating conditions. e) heat rated current (irms) will cause the coil temperature rise approximately t of 40c (keep 1min) f ) saturation current (isat) will cause l0 to drop 20%. c) storage temp. : -40c to +125c b) operating temp. : -40c to +125c a) test freq. : l : 100khz/1.0v h) storage condition (component in its packaging) i) temperature: -10 to 40c ii) humidity : 50~60% rh d) humidity range : 85 3% rh
superworld electronics (s) pte ltd pg. 2 6. electrical characteristics : inductance l0 part no. pic1205hpr33mf 0.33 ( h ) @ 0 a 0.7 dcr typ. @ 25c ( m ) irms ( a ) 42 80 ( a ) isat typ. typ. dcr ( m ) max. @ 25c 0.9 pic1205hpr47mf 0.47 0.86 38 65 1.1 pic1205hpr56mf 0.56 1.0 36 55 1.5 pic1205hpr68mf 0.68 1.4 34 54 1.7 pic1205hp1r0mf 1.00 1.85 29 50 2.5 pic1205hp1r5mf 1.50 2.8 27 48 3.3 pic1205hp1r8mf 1.80 4.0 21 40 4.9 pic1205hp2r2mf 2.20 4.2 20 32 5.5 pic1205hp3r3mf 3.30 6.8 15 32 9.2 pic1205hp4r7mf 4.70 11.4 12 27 15.0 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic1205hp5r6mf pic1205hp6r8mf 5.60 12.3 11.5 22 16.5 6.80 14.5 11 21 18.5 pic1205hp8r2mf 8.20 16.8 9.5 18 22.5 pic1205hp series pic1205hp100mf 10.0 21.4 9.0 16 25.5 pic1205hpr82mf 0.82 1.7 31 52 2.1 pic1205hpr22mf 0.22 0.5 52 110 0.7 pic1205hpr50mf 0.50 0.9 37 60 1.3 06.11.2015 pic1205hpr20mf 0.20 0.45 52 110 0.55 pic1205hpr36mf 0.36 0.75 42 75 0.95 pic1205hpr39mf 0.39 0.78 42 70 0.95 pic1205hp1r2mf 1.20 2.5 28 49 3 pic1205hp6r0mf 6.00 13 11.5 21.5 16.5 pic1205hp150mf 15.0 32 8.2 13 38 PIC1205HP180MF 18.0 40 7.5 11 45 pic1205hp220mf 22.0 50 6.5 10 58 tolerance code : m = 20%, y = 30%
superworld electronics (s) pte ltd pg. 3 7. characteristics curves : smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic1205hp series 06.11.2015 pic1205hpr20mf pic1205hpr22mf pic1205hpr33mf pic1205hpr36mf pic1205hpr39mf pic1205hpr47mf
superworld electronics (s) pte ltd pg. 4 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic1205hp series 06.11.2015 pic1205hpr50mf pic1205hpr56mf pic1205hpr68mf pic1205hpr82mf pic1205hp1r0mf pic1205hp1r2mf
superworld electronics (s) pte ltd pg. 5 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic1205hp series 06.11.2015 pic1205hp1r5mf pic1205hp1r8mf pic1205hp2r2mf pic1205hp3r3mf pic1205hp4r7mf pic1205hp5r6mf
superworld electronics (s) pte ltd pg.6 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. 06.11.2015 pic1205hp series pic1205hp6r0mf pic1205hp6r8mf pic1205hp8r2mf pic1205hp100mf pic1205hp150mf PIC1205HP180MF
superworld electronics (s) pte ltd pg.7 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. 06.11.2015 pic1205hp series pic1205hp220mf
superworld electronics (s) pte ltd pg. 8 8. soldering c) never contact the ceramic with the iron tip e) use a 20 watt soldering iron with tip diameter of 1.0mm d) 1.0mm tip diameter (max) f) limit soldering time to 4~5 secs. 8-1.2 soldering iron (figure 2) : in the event that a soldering iron must be employed the following precautions are recommended. products attachment with soldering iron is discouraged due to the inherent process control limitations. recommended temperature profiles for re-flow soldering in figure 1. mildly activated rosin fluxes are preferred. the minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. our terminations are suitable for all re-flow soldering systems. if hand soldering cannot be avoided, the preferred technique is the utilization of hot air a) preheat circuit and products to 150c. soldering tools. 8-1.1 solder re-flow : note : b) 355c tip temperature (max) temperature c over 1min. gradual cooling within 4-5s 350 150 preheating soldering cooling natural time(sec.) 60~150s 20~40s soldering temperature c 480s max. 60~180s 150 25 tp(260c/40s max.) 217 200 preheating cooling natural figure 1. re-flow soldering: 3 times max. figure 2. hand soldering: 1 times max. smd power choke coil note : specifications subject to change without notice. please check our website for latest information. 06.11.2015 pic1205hp series
superworld electronics (s) pte ltd pg.9 9. packaging information : bz(mm) 13.00.1 9-3. packaging quantity pic1205 series bo(mm) 14.10.1 16.00.1 p(mm) az(mm) 7.00.1 ao(mm) 12.90.1 ko(mm) 5.50.1 240.3 w(mm) 9-2. tape dimension 24.4+2.0/-0 a(mm) 13" x 24mm type 1002 b(mm) d d(mm) 13.50.5 330 c(mm) embossed carrier b a cover tape 9-1. reel dimension pic1205 4000 1000 carton chip / reel inner box size 500 2.00.5 ?c smd power choke coil note : specifications subject to change without notice. please check our website for latest information. 11.50.1 f(mm) b o t bz a o az 3 f w p 1.5 4.0 2.0 1.75 d\c 4r7 0.350.05 t(mm) pic1205hp series d\c 4r7 d\c 4r7 d\c 4r7 d\c 4r7 d\c 4r7 06.11.2015
superworld electronics (s) pte ltd 9-4. tearing off force the force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions. top cover tape f base tape 165 to 180 room temp. (c) 5~35 room humidity (%) 45~85 tearing speed (mm/min) 300 room atm (hpa) 860~1060 pg.10 (referenced ansi/eia-481-c-2003 of 4.11 standard) smd power choke coil note : specifications subject to change without notice. please check our website for latest information. 06.11.2015 pic1205hp series a) products should be handled with care to avoid damage or contamination from perspiration and skin oils. 1. storage conditions : to maintain the solderabililty of terminal electrodes : a) recommended products should be used within 12 months from the time of delivery. b) the packaging material should be kept where no chlorine or sulfur exists in the air. b) vacuum pick up is strongly recommended for individual components. c) bulk handling should ensure that abrasion and mechanical shock are minimized. 2. transportation : application notice
|
